Room-temperature fabrication of fluorinated covalent organic polymer @ Attapulgite composite for in-syringe membrane solid-phase extraction and analysis of domoic acid in aquatic products.

A novel fluorinated covalent organic polymer @ attapulgite composite (F-COP@ATP) was prepared at room temperature for in-syringe membrane solid-phase extraction (SM-SPE) of domoic acid (DA) in aquatic products. Natural ore ATP has the advantages of low cost, good mechanical strength and abundant hydroxyl group on its surface, and in-situ modified F-COP layer can provide abundant adsorption sites. F-COP@ATP combining the advantages of F-COP and ATP, becomes an ideal adsorbent for DA extracting. Moreover, a high-throughput sample preparation strategy was carried out by using the F-COP@ATP membrane as syringe filter and assembling syringes with a ten-channel injection pump. In addition, the experimental factors were optimized, such as pH of extract, amount of adsorbent, velocity of extraction and desorption, type and volume of desorption solvent. The DA analytical method was established by SM-SPE-HPLC/tandem mass spectrometry. The method had a wide linear range with low limit of detection (0.344 ng/kg) and low limit of quantification (1.14 ng/kg). F-COP@ATP membrane can be reused more than five times. The method realized the analysis of DA in scallop and razor clam samples, which shows its application prospect in practical analysis. This study provided an efficient, low-energy and mild idea for preparing other reusable natural mineral ATP-based composite materials for separation and enrichment, which reduces the experimental cost and is closer to environmental protection and green chemistry to a certain extent.

Enhanced efficiencies on purifying acid mine drainage in constructed wetlands based on synergistic adsorption of attapulgite-soda residue composites and microbial sulfate reduction.

Constructed wetlands (CWs) are a promising approach for treating acid mine drainage (AMD). However, the extreme acidity and high loads of heavy metals in AMD can easily lead to the collapse of CWs without proper pre-treatment. Therefore, it is considered essential to maintain efficient and stable performance for AMD treatment in CWs. In this study, pre-prepared attapulgite-soda residue (ASR) composites were used to improve the substrate of CWs. Compared with CWs filled with gravel (CWs-G), the removal efficiencies of sulfate and Fe, Mn, Cu, Zn Cd and Pb in CWs filled with ASR composites (CWs-ASR) were increased by 30% and 10-70%, respectively. These metals were mainly retained in the substrate in stable forms, such as carbonate-, Fe/Mn (oxide)hydroxide-, and sulfide-bound forms. Additionally, higher levels of photosynthetic pigments and antioxidant enzyme activities in plants, along with a richer microbial community, were observed in CWs-ASR than in CWs-G. The application of ASR composites alleviated the adverse effects of AMD stresses on wetland plants and microorganisms. In return, the increased bacteria abundance, particularly SRB genera (e.g., Thermodesulfovibrionia and Desulfobacca), promoted the formation of metal sulfides, enabling the saturated ASR adsorbed with metals to regenerate and continuously capture heavy metals. The synergistic adsorption of ASR composites and microbial sulfate reduction maintained the stable and efficient operation of CWs. This study contributes to the resource utilization of industrial alkaline by-products and promotes the breakthrough of new techniques for low-cost and passive treatment systems such as CWs.

An innovative Fuller's earth-based film-forming formulation for skin decontamination, through removal and entrapment of an organophosphorus compound, paraoxon-ethyl.

Organophosphorus compounds (OPs), such as VX, pose a significant threat due to their neurotoxic and hazardous properties. Skin decontamination is essential to avoid irreversible effects. Fuller's earth (FE), a phyllosilicate conventionally employed in powder form, has demonstrated decontamination capacity against OPs. The aim of this study was to develop a formulation that forms a film on the skin, with a significant OP removal capacity (>95 %) coupled with sequestration capabilities, favorable drying time and mechanical properties to allow for easy application and removal, particularly in emergency context. Various formulations were prepared using different concentrations of polyvinyl alcohol (PVA), FE and surfactants. Their removal and sequestration capacity was tested using paraoxon-ethyl (POX), a chemical that simulates the behavior of VX. Formulations with removal capacity levels surpassing 95 % were mechanically characterized and cell viability assays were performed on Normal Human Dermal Fibroblast (NHDF). The four most promising formulations were used to assess decontamination efficacy on pig ear skin explants. These formulations showed decontamination levels ranging from 84.4 ± 4.7 % to 96.5 ± 1.3 %, which is equivalent to current decontamination methods. These results suggest that this technology could be a novel and effective tool for skin decontamination following exposure to OPs.

Medical waste incineration fly ash-based magnesium potassium phosphate cement: Calcium-reinforced chlorine solidification/stabilization mechanism and optimized carbon reduction process strategy.

The traditional solidification/stabilization (S/S) technology, Ordinary Portland Cement (OPC), has been widely criticized due to its poor resistance to chloride and significant carbon emissions. Herein, a S/S strategy based on magnesium potassium phosphate cement (MKPC) was developed for the medical waste incineration fly ash (MFA) disposal, which harmonized the chlorine stabilization rate and potential carbon emissions. The in-situ XRD results indicated that the Cl- was efficiently immobilized in the MKPC system with coexisting Ca2+ by the formation of stable Ca5(PO4)3Cl through direct precipitation or intermediate transformation (the Cl- immobilization rate was up to 77.29%). Additionally, the MFA-based MKPC also demonstrated a compressive strength of up to 39.6 MPa, along with an immobilization rate exceeding 90% for heavy metals. Notably, despite the deterioration of the aforementioned S/S performances with increasing MFA incorporation, the potential carbon emissions associated with the entire S/S process were significantly reduced. According to the Life Cycle Assessment, the potential carbon emissions decreased to 8.35 × 102 kg CO2-eq when the MFA reached the blending equilibrium point (17.68 wt.%), while the Cl- immobilization rate still remained above 65%, achieving an acceptable equilibrium. This work proposes a low-carbon preparation strategy for MKPC that realizes chlorine stabilization, which is instructive for the design of S/S materials.

Ca-Mg modified attapulgite for phosphate removal and its potential as phosphate-based fertilizer.

The urgent concerns of controlling water body eutrophication and the alleviating phosphorus shortage have led to an urgent need for action. The removal of phosphate from polluted waters and its reuse are essential for the prevention of eutrophication and for the sustainable utilization of phosphate resources. In this study, modified attapulgite with different Ca:Mg molar ratios was synthesized to facilitate the recovery of phosphate, with subsequent use of soil fertilizer. Ca-Mg modified attapulgite with the optimal ratio (ACM-5:3) exhibited an exceptional adsorption quality, achieving a maximum adsorption capacity of 63.2 mg/g. The pseudo-second-order model and Langmuir model could well describe the adsorption kinetics and isotherms, respectively. The adsorption mechanism analyses suggested that the interaction between ACM-5:3 and phosphate depended mainly on ion exchange and electrostatic attraction. Moreover, phosphate-laden-ACM-5:3 demonstrated a significant potential as a phosphorus-releasing fertilizer. It could promote corn growth by ensuring a continuous supply of phosphorus and minimizing phosphorus runoff losses. The above results suggested that ACM-5:3 was a potential adsorbent for efficient phosphate removal and recovery.

Improving feed intake and rumen fermentation in lambs using mixed-dimensional attapulgite clay to adsorb naturally occurring mycotoxins.

This experiment was conducted to evaluate the effects of including a mixed-dimensional attapulgite clay (MDA) into a naturally moldly diet for Hu lambs. Fifty male Hu lambs with similar initial body weight (28.24 ±â€…1.80 kg) were randomly allocated into five dietary treatments: a basal diet containing naturally occurring mycotoxins with 0, 0.5, 1.0, and 2.0 kg/t MDA, and basal diet with a commercial mycotoxin adsorbent Solis with montmorillonite as the major component at 1 kg/t. Both MDA and Solis increased average daily gain (ADG) and dry matter intake (DMI; P ≤ 0.004), and there was no difference in growth performance between MDA and Solis (P ≥ 0.26). The final body weight, DMI, and ADG were linearly increased with increasing MDA supplementation (P < 0.01). Lambs treated with both MDA and Solis demonstrated greater apparent digestibility of dry matter (DM), organic matter (OM), and energy compared with the control group (P ≤ 0.03), and there were no differences in nutrient digestibilities between MDA and Solis (P ≥ 0.38). Digestibility of CP was linearly increased with the increasing MDA supplementation (P = 0.01). Neither MDA nor Solis affected rumen total volatile fatty acid (TVFA) concentration (P ≥ 0.39), but decreased the acetate-to-propionate ratio and molar proportion of n-butyrate (P ≤ 0.01), and MDA also increased the concentration of ammonia (P = 0.003). Besides, increasing MDA supplementation linearly reduced the acetate-to-propionate ratio and molar proportion of n-butyrate (P = 0.01), but linearly and quadratically increased the concentration of ammonia (P ≥ 0.003). These results showed that the incorporation of MDA into a naturally moldy diet of Hu lambs yielded comparable results to the Solis product, with higher growth performance and nutrient digestibility but lower acetate-to-propionate ratio observed. In conclusion, including ≥ 1 kg/t of MDA in high mycotoxin risk diets for growing lambs improves feed intake and rumen fermentation.

The issue of mycotoxin-contaminated animal feed has consistently presented a significant challenge in relation to animal health and production. The mixed-dimensional attapulgite clay (MDA) has been proven effective in binding polar mycotoxins such as aflatoxin, while also effectively adsorbing hydrophobic or weakly polar mycotoxins such as zearalenone (ZEN) and ochratoxin. Therefore, this study was undertaken to assess the impact of MDA inclusion in mycotoxin-contaminated diets on performance and rumen fermentation variables in lambs. The results indicated that MDA not only significantly improved the growth performance and nutrient digestibility of Hu lambs but also enhanced the molar proportion of propionate and ammonia concentration, and reduced the acetate to propionate ratio and the molar proportion of n-butyrate.

Acid modified attapulgite loaded with bacillomycin D for mold inhibition and mycotoxin removal.

Molds and mycotoxins pose severe threats to health. Bacillomycin D (BD) can effectively inhibit mold growth. Attapulgite (ATP) can provide a good carrier for antimicrobial agents. Natural ATP was acid-modified to obtain H-ATP. It was used to load BD to obtain a novel composite material (H-ATP-BD). The results showed H-ATP had better adsorption performance than ATP. BD was adsorbed up to 93.13 % by adding 30 mg H-ATP and stirring at 40 ℃ for 120 min. Fourier transform infrared spectra (FTIR), size and zeta potential, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) results confirmed successful loading of BD onto H-ATP. The composite showed good inhibition of Aspergillus and adding 0.6 % H-ATP-BD composite was effective in removing 89.06 % of aflatoxin B1 (AFB1) at 50 °C. Model fitting indicated that AFB1 removal was a spontaneous exothermic reaction. This research will lay the foundation for the development of efficient and green antimicrobial and toxin-reducing materials.

Competitive encapsulation of multiple heavy metals by magnesium potassium phosphate cement: Hydration characteristics and leaching toxicity properties.

Magnesium potassium phosphate cement (MKPC) is increasingly used in the solidification/stabilization (SS) of heavy metal (HM) pollutants. However, research on composite HM pollutants remains limited. In this study, four heavy metals (Pb/Zn/Cu/Cd) were individually and simultaneously introduced into MKPC systems with different magnesium/phosphorus (M/P) molar ratios. The introduction of HMs altered the extent of hydration and morphology of MgKPO4·6H2O. Among the MKPC pastes, those with M/P = 2 and 3 had the highest HM solidification efficiency and strength, respectively. The HM solidification efficiency of all specimens exceeded 99 %. In samples with M/P = 3, the codoping of four HMs slightly increased the M/P ratio, thereby increasing MgKPO4·6H2O content and enhancing strength. Pb could generate additional low-solubility precipitates, such as PbHPO4, Pb3 (PO4)2, Pb5 (OH) (PO4)3, and Pb (OH)2, which easily accumulated in pores and were encapsulated by MgKPO4·6H2O, leading to the highest solidification efficiency of Pb by MKPC. Pb and Cu could also form the composite phosphate products Pb2Cu (PO4)3 (OH)·4H2O, thus promoting the S/S effect of Cu. Therefore, the use of MKPC with M/P ratio of 2-3 for the S/S of complex pollutants containing Pb and Cu is a promising approach.

Comparison of calcium magnesium ferrite nanoparticles for boosting biohydrogen production.

Dark fermentation (DF) is an eco-friendly process that simultaneously achieves organic matter degradation and obtains hydrogen (H2). Nonetheless, low H2 yield mainly caused by poor activity of key microbes, is still a problem that requires being resolved. In this work, MgFe2O4 and Ca0.5Mg0.5Fe2O4 nanoparticles (NPs) were synthetized and served as additives to boost H2 form from DF. H2 productivity gradually increased with the rise of NPs, and declined when NPs exceeded their optimal dosages. The highest H2 yield was 183.6 ± 3.2 mL/g glucose at 100 mg/L of MgFe2O4 NPs, being 35.2 % higher than that of the control yield (135.8 ± 3.1 mL/g glucose). However, the highest H2 yield of 171.9 ± 2.5 mL/g glucose occurred at 400 mg/L of Ca0.5Mg0.5Fe2O4 NPs, increasing by 26.6 % over the control. Interestingly, the two NPs favored the butyric acid pathway for H2 synthesis. This provides guidance for multi-element oxide NPs used in DF.

Copper-doped magnesium phosphate nanopowders for critical size calvarial bone defect intervention.

Calvarial defects of bone present difficult clinical situations, and their restoration using biocompatible materials requires special treatments that enable bone regeneration. Magnesium phosphate (MgP) is known as an osteoinductive biomaterial because it contains Mg2+ ions and P ions that enhance the activity of osteoplast cells and help in bone regeneration. In this study, MgP and CuO-doped MgP were fabricated and characterized for their physicomechanical properties, particle size, morphology, surface area, antibacterial test, and in vitro bioactivity evaluation using the following techniques: X-rays diffraction, Fourier-transformer infrared, TEM, and Brunauer, Emmett and Teller (BET) surface area, X-rays photoelectron spectroscopy (XPS), and Scanning electron microscopy (SEM). Furthermore, these nanopowders were implanted in adult inbred male Wistar rats and studied after two periods (28 and 56 days). The results demonstrated that the obtained semiamorphous powders are in nanoscale (≤ 50 nm). XPS analysis ensured the preparation of MgP as mono MgP and CuO were incorporated in the structure as Cu2+ . The bioactivity was supported by the observation of calcium phosphate layer on the nanopowders' surface. The in vivo study demonstrated success of MgP nanopowders especially those doped with CuO in restoration of calvarial defect bone. Therefore, fabricated biomaterials are of great potential in restoration of bone calvarial defects.

3D-Printed Magnesium Peroxide-Incorporated Scaffolds with Sustained Oxygen Release and Enhanced Photothermal Performance for Osteosarcoma Multimodal Treatments.

The hypoxic microenvironment in osteosarcoma inevitably compromises the antitumor effect and local bone defect repair, suggesting an urgent need for sustained oxygenation in the tumor. The currently reported oxygen-releasing materials have short oxygen-releasing cycles, harmful products, and limited antitumor effects simply by improving hypoxia. Therefore, the PCL/nHA/MgO2/PDA-integrated oxygen-releasing scaffold with a good photothermal therapy effect was innovatively constructed in this work to achieve tumor cell killing and bone regeneration functions simultaneously. The material distributes MgO2 powder evenly on the scaffold material through 3D printing technology and achieves the effect of continuous oxygen release (more than 3 weeks) through its slow reaction with water. The in vitro and in vivo results also indicate that the scaffold has good biocompatibility and sustained-release oxygen properties, which can effectively induce the proliferation and osteogenic differentiation of bone mesenchymal stem cells, achieving excellent bone defect repair. At the same time, in vitro cell experiments and subcutaneous tumorigenesis experiments also confirmed that local oxygen supply can promote osteosarcoma cell apoptosis, inhibit proliferation, and reduce the expression of heat shock protein 60, thereby enhancing the photothermal therapy effect of polydopamine and efficiently eliminating osteosarcoma. Taken together, this integrated functional scaffold provides a unique and efficient approach for antitumor and tumor-based bone defect repair for osteosarcoma treatment.

Development of natural attapulgite derived ferromanganese spinel oxides as heterogeneous catalysts for persulfate activation of tetracycline degradation.

Ferromanganese spinel oxides (MnFe2O4, MFO) have been proven effective in activating persulfate for pollutants removal. However, their inherent high surface energy often leads to agglomeration, diminishing active sites and consequently restricting catalytic performance. In this study, using Al-MCM-41 (MCM) mesoporous molecular sieves derived from natural attapulgite as a support, the MFO/MCM composite was synthesized through dispersing MnFe2O4 nanoparticles on MCM carrier by a simple hydrothermal method, which can effectively activate persulfate (PS) to degrade Tetracycline (TC). The addition of Al-MCM-41 can effectively improve the specific surface area and adsorption performance of MnFe2O4, but also reduce the leaching amount of metal ions. The MFO/MCM composite exhibited superior catalytic reactivity towards PS and 84.3% removal efficiency and 64.7% mineralization efficiency of TC (20 mg/L) was achieved in 90 min under optimized conditions of 0.05 mg/L catalyst dosage, 5 mM PS concentration, room temperature and no adjustment of initial pH. The effects of various stoichiometric MFO/MCM ratio, catalyst dosage, PS concentration, initial pH value and co-existing ions on the catalytic performance were investigated in detail. Moreover, the possible reaction mechanism in MFO-MCM/PS system was proposed based on the results of quenching tests, electron paramagnetic resonance (EPR) and XPS analyses. Finally, major degradation intermediates of TC were detected by liquid chromatography mass spectrometry technologies (LC-MS) and four possible degradation pathways were proposed. This study enhances the design approach for developing highly efficient, environmentally friendly and low-cost catalysts for the advanced treatment process of antibiotic wastewater.

Amorphous magnesium phosphate-graphene oxide nano particles laden 3D-printed chitosan scaffolds with enhanced osteogenic potential and antibacterial properties.

The utilization of 3D printing technology for the fabrication of graft substitutes in bone repair holds immense promise. However, meeting the requirements for printability, bioactivity, mechanical strength, and biological properties of 3D printed structures concurrently poses a significant challenge. In this study, we introduce a novel approach by incorporating amorphous magnesium phosphate-graphene oxide (AMP-GO) into a thermo-crosslinkable chitosan/ß glycerol phosphate (CS/GP) ink. We fabricated thermo-crosslinkable CS inks containing varying concentrations (10 %, 20 %, or 30 % weight) of AMP-GO. The 3D printed scaffolds incorporating 20 % AMP-GO exhibited significantly improved mechanical properties, with compressive strengths of 4.5 ± 0.06 MPa compared to 0.5 ± 0.03 MPa for CS printed scaffolds. Moreover, the CS/AMP-GO inks demonstrated enhanced antibacterial activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria, attributed to the release of magnesium cations and the performance of GO. Additionally, CS/20AMP-GO ink facilitated increased adhesion, viability, proliferation, and osteogenic differentiation of mesenchymal stem cells (MSCs), as evidenced by the upregulation of ALP, COL1, and Runx2 expression, which were elevated 9.8, 6.5, and >22 times, respectively, compared to pure CS scaffolds. Considering its exceptional in vivo osteogenic potential, we anticipate that the CS/20AMP-GO ink holds great potential for 3D printing of bone grafts.

Improving bone defect healing using magnesium phosphate granules with tailored degradation characteristics.

OBJECTIVES: Dental implant placement frequently requires preceding bone augmentation, for example, with hydroxyapatite (HA) or ß-tricalcium phosphate (ß-TCP) granules. However, HA is degraded very slowly in vivo and for ß-TCP inconsistent degradation profiles from too rapid to rather slow are reported. To shorten the healing time before implant placement, rapidly resorbing synthetic materials are of great interest. In this study, we investigated the potential of magnesium phosphates in granular form as bone replacement materials. METHODS: Spherical granules of four different materials were prepared via an emulsion process and investigated in trabecular bone defects in sheep: struvite (MgNH4PO4·6H2O), K-struvite (MgKPO4·6H2O), farringtonite (Mg3(PO4)2) and ß-TCP. RESULTS: All materials except K-struvite exhibited promising support of bone regeneration, biomechanical properties and degradation. Struvite and ß-TCP granules degraded at a similar rate, with a relative granules area of 29% and 30% of the defect area 4 months after implantation, respectively, whereas 18% was found for farringtonite. Only the K-struvite granules degraded too rapidly, with a relative granules area of 2% remaining, resulting in initial fibrous tissue formation and intermediate impairment of biomechanical properties. SIGNIFICANCE: We demonstrated that the magnesium phosphates struvite and farringtonite have a comparable or even improved degradation behavior in vivo compared to ß-TCP. This emphasizes that magnesium phosphates may be a promising alternative to established calcium phosphate bone substitute materials.

Regulating pathway for bacterial diversities toward improved ecological benefits of thiencarbazone-methyl·isoxaflutole application: A field experiment.

Herbicide abuse has a significantly negative impact on soil microflora and further influences the ecological benefit. The regulating measures and corresponding mechanisms mitigating the decreased bacterial diversity due to herbicide use have rarely been studied. A field experiment containing the application gradient of an efficient maize herbicide thiencarbazone-methyl·isoxaflutole was performed. The relationship between soil bacterial community and thiencarbazone-methyl·isoxaflutole use was revealed. Modified attapulgite was added to explore its impacts on soil microflora under the thiencarbazone-methyl·isoxaflutole application. Based on the analytic network process-entropy weighting method-TOPSIS method model, the ecological benefit focusing on microbial responses was quantitatively estimated along with technical effectiveness and economic benefit. The results showed that the diversity indices of soil microflora, especially the Inv_Simpson index, were reduced at the recommended, 5 and 10 times the recommended dosages of thiencarbazone-methyl·isoxaflutole use. The Flavisolibacter bacteria was negatively correlated with the residues in soils based on the random forest model and correlation analysis, indicating a potential degrader of thiencarbazone-methyl·isoxaflutole residues. The structural equation model further confirmed that the high soil water content and soil pH promoted the function of Flavisolibacter bacteria, facilitated the dissipation of thiencarbazone-methyl·isoxaflutole residues and further improved the diversity of soil microflora. In addition, the presence of modified attapulgite was found to increase the soil pH, which may improve bacterial diversity through the regulating pathway. This explained the high ecological benefits of the treatment where the thiencarbazone-methyl·isoxaflutole was applied at the recommended dosage rates in conjunction with modified attapulgite addition. Therefore, the comprehensive benefits of thiencarbazone-methyl·isoxaflutole application with a focus on ecological benefits can be improved by regulating the soil pH with modified attapulgite.

Development of Magnesium Aluminate (MgAl2O4) Nanoparticles for refractory crucible application.

Ceramics are the oxides of metals and nonmetals with excellent compressive strength. Ceramics usually exhibit inert behavior at high temperatures. Magnesium aluminate (MgAl2O4), a member of the ceramic family, possesses a high working temperature up to 2000°C, low thermal conductivity, high strength even at elevated temperatures, and good corrosion resistance. Moreover, Magnesium Aluminate Nanoparticles (MANPs) can be used in the making of refractory crucible applications. This study focuses on the thermal behavior of Magnesium Aluminate Nanoparticles (MANPs) and their application in the making of refractory crucibles. The molten salt method is used to obtain MANPs. The presence of MANPs is seen by XRD peaks ranging from 66° to 67°. The determination of the smallest crystallite size of the sample is achieved by utilizing the Scherrer formula and is found to be 15.3 nm. The SEM micrographs provided further information, indicating an average particle size of 91.2 nm. At 600°C, DSC curves show that only 0.05 W/g heat flows into the material, and the TGA curve shows only 3% weight loss, which is prominent for thermal insulation applications. To investigate the thermal properties, crucibles of pure MANPs and the different compositions of MANPs and pure alumina are prepared. During the sintering, cracks appear on the crucible of pure magnesium aluminate. To explore the reason for crack development, tablets of MgAl2O4 are made and sintered at 1150°C. Ceramography shows the crack-free surfaces of all the tablets. Results confirm the thermal stability of MANPs at high temperatures and their suitability for melting crucible applications.

The interactions between olivine dissolution and phytoplankton in seawater: Potential implications for ocean alkalinization.

Ocean alkalinity enhancement, one of the ocean-based CO2 removal techniques, has the potential to assist us in achieving the goal of carbon neutrality. Olivine is considered the most promising mineral for ocean alkalinization enhancement due to its theoretically high CO2 sequestration efficiency. Olivine dissolution has been predicted to alter marine phytoplankton communities, however, there is still a lack of experimental evidence. The olivine dissolution process in seawater can be influenced by a range of factors, including biotic factors, which have yet to be explored. In this study, we cultivated two diatoms and one coccolithophore with and without olivine particles to investigate their interactions with olivine dissolution. Our findings demonstrate that olivine dissolution promoted the growth of all phytoplankton species, with the highly silicified diatom Thalassiosira pseudonana benefiting the most. This was probably due to the highly silicified diatom having a higher silicate requirement and, therefore, growing more quickly when silicate was released during olivine dissolution. Based on the structural characteristics and chemical compositions on the exterior surface of olivine particles, T. pseudonana was found to promote olivine dissolution by inhibiting the formation of the amorphous SiO2 layer on the surface of olivine and therefore enhancing the stoichiometric dissolution of olivine. However, the positive effects of T. pseudonana on olivine dissolution were not observed in the coccolithophore Gephyrocapsa oceanica or the non-silicate obligate diatom Phaeodactylum tricornutum. This study provides the first experimental evidence of the interaction between phytoplankton and olivine dissolution, which has important implications for ocean alkalinization research.

An injectable bioactive poly(γ-glutamic acid) modified magnesium phosphate bone cement for bone regeneration.

As potential alternatives for calcium phosphate bone cements, magnesium phosphate bone cements (MPC) have attracted considerable attention in recent years. However, their several defects, such as rapid setting times, highly hydration temperature and alkaline pH due to the part of the unreacted phosphate, restricted their applications in human body. With aim to overcome these defects, a novel polypeptite poly(γ-glutamic acid) (γ-PGA) modified MPC were developed. Effect of γ-PGA content on the injectability, anti-washout ability, setting times, hydration temperature, mechanical compressive strength, in vitro bioactivity and degradation were investigated. Moreover, in vitro cyto-compatibility was evaluated using MC3T3-E1 cells by CCK-8 and Live/Dead staining. All these results indicated that the 10%PGA-MPC with an improved handling performances, low hydration temperature, high mechanical compressive strength, and good cyto-compatibility hold a great potential for bone repair and regeneration.

Trends in urolith composition and factors associated with different urolith types in dogs from the Republic of Ireland and Northern Ireland between 2010 and 2020.

OBJECTIVES: The purpose of this study was to determine changes in urolith trends and factors associated with different urolith types in dogs from the Republic of Ireland and Northern Ireland between 2010 and 2020. MATERIALS AND METHODS: A laboratory database was searched for canine urolith submissions between 2010 and 2020. Trends in urolith composition between 2014 and 2020, and associations between patient characteristics with each urolith type were evaluated. RESULTS: A total of 1162 submissions were included. Struvite (39.0%), calcium oxalate (27.8%) and compound (10.2%) were the most prevalent uroliths. Calcium oxalate urolith (CaOx) incidence significantly increased from 27.8% to 31.2% and that of struvite significantly decreased from 41.7% to 33.0% between 2014 and 2020. Struvite uroliths were overrepresented among females compared to males (odds ratio 8.7, 95% confidence interval 6.6 to 11.5). Males (odds ratio 9.6, 95% confidence interval 6.9 to 13.3) and dogs >7 years of age (odds ratio 4.1, 95%, confidence interval 3.0 to 5.4) were more likely to have CaOx while males (odds ratio 9.6, 95% confidence interval 5.3 to 17.8) and dogs ≤7 year of age, purine uroliths (odds ratio 3.0, 95% confidence interval 1.8 to 5.0). Incidence was higher in bichon frise (odds ratio 1.7, 95% confidence interval 1.3 to 2.4) and Yorkshire terrier (odds ratio 2.8, 95% confidence interval 1.9 to 4.1) for CaOx and higher in shih-tzu for compound uroliths (odds ratio 1.7, 95% confidence interval 1.1 to 2.7) compared to the remaining reported breeds. CLINICAL SIGNIFICANCE: Factors associated with different uroliths were similar to the ones previously reported. Proportion of CaOx submissions increased and that of struvite decreased over the study period which was in agreement with the changes identified in other European countries.

Olivine avoidance behaviour by marine gastropods (Littorina littorea L.) and amphipods (Gammarus locusta L.) within the context of ocean alkalinity enhancement.

Gigaton scale atmospheric carbon dioxide (CO2) removal (CDR) is needed to keep global warming below 1.5 °C. Coastal enhanced olivine weathering is a CDR technique that could be implemented in coastal management programmes, but its CO2 sequestration potential and environmental safety remain uncertain. Large scale olivine spreading would change the surficial sediment characteristics, which could potentially reduce habitat suitability and ultimately result in community composition changes. To test this hypothesis, we investigated the avoidance response of the marine gastropod Littorina littorea (Linnaeus, 1758) and marine amphipod Gammarus locusta (Linnaeus, 1758) to relatively coarse (83 - 332 µm) olivine and olivine-sediment mixtures during short-term choice experiments. Pure olivine was significantly avoided by both species, while no significant avoidance was observed for sediment with 3% or 30% w/w olivine. For L. littorea, aversion of the light green colour of pure olivine (i.e. positive scototaxis) was the main reason for avoidance. Moreover, olivine was not significantly avoided when it was 7.5 cm (45%) closer to a food source/darker microhabitat (Ulva sp.) compared to natural sediment. It is inferred that the amphipod G. locusta avoided pure olivine to reduce Ni and Cr exposure. Yet, a significant increase in whole body Ni concentrations was observed after 79 h of exposure in the 30% and 100% w/w olivine treatments compared to the sediment control, likely as a result of waterborne Ni uptake. Overall, our results are significant for ecological risk assessment of coastal enhanced olivine weathering as they show that L. littorea and G. locusta will not avoid sediments with up to 30% w/w relatively coarse olivine added and that the degree of olivine avoidance is dependent on local environmental factors (e.g. food or shelter availability).